Content
# #tough-smr — 2025-05-30
**15:22 [Kevin](https://slack.com/archives/C08NFJSU753/p1748643740670629):** @Mason Radke I just got to SMR
**15:22 [Kevin](https://slack.com/archives/C08NFJSU753/p1748643777121599):** Figured I'd wait until it was 95 deg
**15:35 [Kevin](https://slack.com/archives/C08NFJSU753/p1748644546035729):** @andy do you want to check with the County to see if they are going to commission the analyzers or are we? They finally have everything plumbed in
**15:36 [andy](https://slack.com/archives/C08NFJSU753/p1748644582846689):** We are
**15:36 [Kevin](https://slack.com/archives/C08NFJSU753/p1748644609045119):** Copy. Do wr want to do it now?
**16:10 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748646615378319):** I’m ready. Let me know where you want to start
**16:12 [andy](https://slack.com/archives/C08NFJSU753/p1748646723342109):** Kyle at county said he will check with his team Monday if you haven’t set them up yet.
**16:12 [andy](https://slack.com/archives/C08NFJSU753/p1748646728365789):** Just called him
**16:13 [Kevin](https://slack.com/archives/C08NFJSU753/p1748646796753959):** @andy I have not. I will standby on setting up the analyzers.
**16:13 [Kevin](https://slack.com/archives/C08NFJSU753/p1748646818460449):** @Mason Radke can you see why the wells are in fault?
**16:14 [Kevin](https://slack.com/archives/C08NFJSU753/p1748646851597019):** @andy we need another one of these cables
![[F08V56F8ECR_20250530_161224.jpg]]
**16:17 [andy](https://slack.com/archives/C08NFJSU753/p1748647050311989):** I have all of them I can give you
**16:26 [Kevin](https://slack.com/archives/C08NFJSU753/p1748647611879069):** Copy
**16:27 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647668887599):** oh. dont clear well 6 so i can chase it down
**16:27 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647673234559):** did you just clear 5?
**16:28 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647688637679):** ah, theyr'e both going
**16:30 [Kevin](https://slack.com/archives/C08NFJSU753/p1748647837778649):** Sorry
**16:30 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647855849509):** its a weird pax thing for sure. just need to figure out what it is.
**16:31 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647867249869):** whats next
**16:31 [Kevin](https://slack.com/archives/C08NFJSU753/p1748647877465449):** Why are both wells running?
**16:31 [Kevin](https://slack.com/archives/C08NFJSU753/p1748647903941039):** And why is W6 only 45 hz
**16:31 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647903973229):** let me look..
**16:32 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647922619799):** w6 is only 45hz because it hasnt reached its flow setpoint to release to PID control
**16:32 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647934917149):** the threshold needs to be lowered.
**16:32 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748647960310299):**
![[F08UQDLHRK7_image.png]]
**16:33 [Kevin](https://slack.com/archives/C08NFJSU753/p1748647986154119):** Copy
**16:33 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648014069479):**
![[F08UU0J9KT4_img_20250530_163313.jpg]]
**16:36 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648194136359):** lag call must have been latched while they were faulted.. and after you cleared they both started..
**16:36 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648209499889):** lag pump will stop at setpoint.. or we can simulate tank level for a second to test the lag stop
**16:37 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648228543509):** Ok we can let it do it's thing
**16:38 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648318184589):** Let's figure out booster status.
**16:38 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648322430459):** sounds good
**16:39 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648351792889):** I have p3 on at 900 rpm
**16:39 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648362214629):** In hand on vfd
**16:39 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648367917119):** ok, standby
**16:42 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648542722829):** hm, i dont have a 1 for running status but i do see a speed value of 4173
**16:42 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648562429599):** i can infer running status if speed >0
**16:42 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648564656309):** if we have to
**16:43 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648627504369):** It doesn't show running on the CU352 either
**16:44 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648643512189):** Gonna try auto
**16:45 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648703503109):** How about now?
**16:45 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648717513119):** i see pump1 and pump3 running
**16:46 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648782967219):** linking up some things to the pax object
**16:46 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748648790858459):** we need to figure out the scaling on this speed value
**16:46 [Kevin](https://slack.com/archives/C08NFJSU753/p1748648802587569):** Copy
**16:57 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649478780729):** ok.. its blue.. some pax stuff to figure out on why it doesnt think its running
**16:58 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649486503919):** what is the actual speed of the pump?
**16:58 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649499840609):** 28pct
**16:58 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649525062699):** Now 1247rpm
**16:58 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649528775739):** Set to hand
**16:59 [andy](https://slack.com/archives/C08NFJSU753/p1748649553750309):** Blue is starting, (run command but no feedback)
**16:59 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649576152079):** yeah. but im feeding it the run signal... it could also be stopping.. (running but no run cmd)
**17:01 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649660134689):** I have it at 10pct
**17:01 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649679887019):** fixed?
**17:01 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649683910129):** it should stay there/
**17:01 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649713737569):** Fixed. But min speed is 900rpm so thats where it's at now
**17:02 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649742924209):** are you able to run it 100% for a short period of rtime?
**17:02 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649749291859):** Yes
**17:02 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649761722799):** that will be helpful.. lets see what that raw value is
**17:02 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649771260209):** Here goes
**17:03 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649798317789):** 50pct 1800rpm
**17:03 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649814992609):** ok! well that makes sense kinda.. i have 5000
**17:03 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649817487789):** that could be 50%
**17:03 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649829135299):** 5984 now
**17:03 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649837806019):** 8000
**17:04 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649854799419):** 100
**17:04 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649863306029):** ok, its 10000
**17:04 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649871382889):** so i think we can assume the feedback is %*100
**17:04 [Kevin](https://slack.com/archives/C08NFJSU753/p1748649894736639):** 50
**17:05 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649931886729):** this isnt making sense from the faceplate
**17:05 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649958562829):**
![[F08ULA8MBGB_image.png]]
**17:05 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649959964549):** 5000 going into the object
**17:06 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649977648799):**
![[F08UDF3SSFR_image.png]]
**17:06 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649979381239):** 25000 showing on the faceplate
**17:06 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649992415619):** standby.
**17:06 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748649995072229):** investigating
**17:19 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748650756722389):** boom
**17:19 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748650759386849):**
![[F08V5AB3XQ9_image.png]]
**17:19 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748650777559759):** i updated the UDT to grab the speed feedback input and updated the faceplate to display the actual input
**17:19 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748650783001739):** now things are making sense
**17:20 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748650805640729):** let me work on the stopping status now
**17:41 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652082129579):** ok.
**17:41 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652084138889):** got her sorted out
**17:41 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652088848059):**
![[F08ULC6EY3D_image.png]]
**17:41 [Kevin](https://slack.com/archives/C08NFJSU753/p1748652107130009):** Nice!
**17:42 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652129633879):** i'll work on updating the other 2 pumps
**17:42 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652137313729):** let me know whats next after that..
**17:42 [Kevin](https://slack.com/archives/C08NFJSU753/p1748652152584799):** Other 5 pumps
**17:42 [Kevin](https://slack.com/archives/C08NFJSU753/p1748652161819999):** 4 boosters 2 transfers
**17:43 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652190422889):** can you switch to booster pump 1?
**17:43 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652196408389):** at whatever speed you want
**17:44 [Kevin](https://slack.com/archives/C08NFJSU753/p1748652264866069):** Running
**17:48 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652504215379):**
![[F08ULCJL57V_image.png]]
**17:48 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652505234259):** pump 1
**17:48 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652510157109):** does the speed look correct?
**17:52 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652727685009):** can you switch to pump 2 after you confirm the speed looks good
**17:55 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748652949275749):** well 6 is faulted.. im checking the fault. now
**17:58 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653131972459):** heatsink overtemp
**17:58 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653139212739):** probably because its hot as balls out there?
**17:59 [Kevin](https://slack.com/archives/C08NFJSU753/p1748653148440679):** Copy. P1 is good
**17:59 [Kevin](https://slack.com/archives/C08NFJSU753/p1748653153937039):** Yeah probably
**17:59 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653156573669):** P2 is ready to test
**17:59 [Kevin](https://slack.com/archives/C08NFJSU753/p1748653162743629):** P2 running
**17:59 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653184319819):** whats the discharge pressure?
**18:00 [Kevin](https://slack.com/archives/C08NFJSU753/p1748653222601039):** 77
**18:00 [Kevin](https://slack.com/archives/C08NFJSU753/p1748653257344459):** Running up to W6
**18:01 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653264605539):** i can reset it from here
**18:01 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653270028769):** but maybe there is a thermostat that can be adjusted?
**18:03 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653426295409):**
![[F08UDJ5TKJT_image.png]]
**18:03 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653429578189):** got system pressure linked up and scaled
**18:05 [Kevin](https://slack.com/archives/C08NFJSU753/p1748653517531549):** The cooling fans aren't running on the W6 vfd @andy
**18:09 [Kevin](https://slack.com/archives/C08NFJSU753/p1748653759389919):** Stupid drives show you everything except the heatsink temp
**18:09 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748653772987409):** i might be able to see it
**18:14 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654044725159):** im not seeing it.. probably because its a PF70
**18:14 [Kevin](https://slack.com/archives/C08NFJSU753/p1748654060519179):** Was that POS 70?
**18:14 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654080364379):** i think so yes.
**18:15 [Kevin](https://slack.com/archives/C08NFJSU753/p1748654107131559):** Booster 2 is at 30hz
**18:15 [Kevin](https://slack.com/archives/C08NFJSU753/p1748654118194489):** Only shows 19.85
**18:15 [Kevin](https://slack.com/archives/C08NFJSU753/p1748654130489399):** Better
**18:15 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654134337919):** yes.
**18:15 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654135054159):** fixed
**18:16 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654164250489):** can we run the high flow?
**18:16 [Kevin](https://slack.com/archives/C08NFJSU753/p1748654190544549):** No. It makes a terrible noise
**18:16 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654206254089):** ok, ill make the same logic and scada changes.
**18:16 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654211268499):** it should be good
**18:17 [Kevin](https://slack.com/archives/C08NFJSU753/p1748654225574389):** We can run transfer pumps at low speed
**18:17 [Kevin](https://slack.com/archives/C08NFJSU753/p1748654256001549):** If you are ready for those
**18:17 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654262895169):** just a minute
**18:26 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654802342639):** ok transfer pump 1 is ready
**18:26 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654808155059):** i also scaled the flow setpoint properly on scada
**18:26 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654814241669):** wait..
**18:26 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654817270169):** no i didnt
**18:27 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654839075039):** thats going to take some figuring out
**18:27 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748654847871549):** but pump1 is ready for status testing
**18:31 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655115388039):** K here goes
**18:32 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655153635189):** without the system enable bit, we dont get run status back
**18:33 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655190822069):** i can fake it.. if we have feedback we can assume its running
**18:33 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655204310789):** K. You see speed?
**18:33 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655206997009):** yes
**18:33 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655218557249):**
![[F08UU7GTTMG_image.png]]
**18:33 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655236238239):** should i work on the run status modification?
**18:34 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655242039939):** once its in auto we will get the actual run status
**18:34 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655275660929):** No it's ok
**18:34 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655282695559):** 50pct?
**18:34 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655299178829):** yes sir
**18:35 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655301006149):**
![[F08UMDT8REJ_image.png]]
**18:35 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655324299519):** Cool
**18:40 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655608394909):** Test p2?
**18:40 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655611318109):** ready
**18:40 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655656525549):** 50pct
**18:41 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655670999829):** copy that
**18:41 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655671711719):**
![[F0902TPPF32_image.png]]
**18:42 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655732230669):** Fault status from CU?
**18:42 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655742276089):** can we make a fault status?
**18:42 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655774218779):**
![[F08UDL0HSPR_img_20250530_184236.jpg]]
**18:43 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655798373969):** is it clearable? (for testing? let me locate the bit first)
**18:43 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655807113249):** Yes
**18:45 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655920197439):** hm.. go ahead and clear it
**18:45 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655932874349):** Clear
**18:46 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655976624489):** which system are we looking at?
**18:46 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655980228899):** transfer or booster
**18:46 [Kevin](https://slack.com/archives/C08NFJSU753/p1748655983677069):** Transfer
**18:46 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655988209219):** oh.. ok.. lets try again
**18:46 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748655989716769):** can you fault it
**18:46 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656008419239):** Fault
**18:48 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656089639619):** is this comm fault for pump1?
**18:48 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656093943329):** Yep
**18:48 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656115319069):** ok.. where do we want to see this?
**18:48 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656134122579):** drive fault on the faceplate?
![[F08UU86RBLJ_image.png]]
**18:50 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656210779489):** 10 min till beer thirty
**18:50 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656245783789):** Is this going to be a generic fault for the whole system?
**18:51 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656272287899):** i dont know. thats my question as well
**18:51 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656287888959):** Let's try p2 fault?
**18:51 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656289242419):** that particular fault came in on pump 1
**18:51 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656312727369):** I can cause a general fault
**18:52 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656334050579):** K general fault
**18:52 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656341289479):** Or system fault maybe
**18:53 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656394852969):** there is an alarm code
![[F08UMENT63Y_image.png]]
**18:53 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656413071439):**
![[F08UDLFSPPZ_image.png]]
**18:53 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656417156739):** and it shows both pumps in alarm
**18:54 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656456341609):** Ok so we have an alarm for each pump, and a system alarm.
**18:54 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656474864319):** So set the pump alarms on the pump faceplates
**18:54 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656489253829):** how do we identify the system alarm?
**18:54 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656497202649):** And create a Pdin?
**18:55 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656527652369):** well. i think we'll feed the pump alarm statuses into the VSD object directly
**18:55 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656538106279):** Yes
**18:55 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656546565659):** not sure what to do with the alarm code.
**18:56 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656560539649):** we'll have to map certain values to statuses?
**18:56 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656580791529):** Maybe just if>0=alarm?
**18:56 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656617364089):** we'll have to verify thats the case
**18:56 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748656619399379):** but we could do that
**18:57 [Kevin](https://slack.com/archives/C08NFJSU753/p1748656636387919):** All faults clear
**19:05 [Kevin](https://slack.com/archives/C08NFJSU753/p1748657137796719):** I'm heading home
**19:05 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748657152858859):** ok.. im just linking up that alarm bit to the pax objects
**19:05 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748657156884099):** then i'll close out too
**19:06 [Kevin](https://slack.com/archives/C08NFJSU753/p1748657181940019):** Thanks for your work today
**19:06 [Mason Radke](https://slack.com/archives/C08NFJSU753/p1748657197003819):** no problem! we made some more progress.. we're getting there
**19:06 [Kevin](https://slack.com/archives/C08NFJSU753/p1748657212899929):** It's real close!