Content
# #ccsd-water-ignition — 2025-08-26
**07:43 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756219382662709):** This is helpful. It was hard to tell how much vertical real estate I had to work with
**10:42 [andy](https://slack.com/archives/C08TVA84PD4/p1756230129745549):** Yeah, the toolbars tabs headers really consume a lot
**10:42 [andy](https://slack.com/archives/C08TVA84PD4/p1756230171356609):** I'm not sure why but even horizontal space appears to be encroached but certainly by a less amount
**10:43 [andy](https://slack.com/archives/C08TVA84PD4/p1756230208383509):** And I created two tabs for WRF only because I don't know how to create the tabs within the tab that you did. I would prefer WRF, then Analogs and Discrete tabs for 207 and 208
**12:51 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756237895218309):** copy that.
**13:18 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756239503799349):** @andy from these screenshots. its it just the well pages that dont fit vertically?
**13:19 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756239540846019):** and what are you seeing horizontally that i can fix?
**13:19 [andy](https://slack.com/archives/C08TVA84PD4/p1756239592665419):** You don’t see things getting cut off on the right side of these screenshots?
**13:20 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756239631275209):** oh yes i do.
**13:20 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756239633532059):** but just on the well pages
**13:20 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756239657382419):** will the other views work as they are currently laid out?
**13:25 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756239956499889):**
![[F09C56SEBRQ_image.png]]
**13:26 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756239977302749):** also did something change here? it shows the Analog label twice.. and the value is getting cut off
**14:12 [andy](https://slack.com/archives/C08TVA84PD4/p1756242734758619):** Hm, I changed the analog value display to show both short and long names, I would like to make room for that on the larger analog view if you can
**14:13 [andy](https://slack.com/archives/C08TVA84PD4/p1756242783622719):** The other views look OK, they don't seem to be causing scroll bars even though they are too large, they just don't show content over there. Please figure out the right dimension and apply to all the views so we don't have an issue further down the line
**14:13 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756242827636759):** ill see what i can do. i may need you to verify how it looks since i dont have an ipad
**14:14 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756242840849109):** the embedded wells page with its tabs is being tricky
**14:14 [andy](https://slack.com/archives/C08TVA84PD4/p1756242849692279):** I can get you one for testing, I do this on every project
**14:14 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756242860290729):** sounds good
**15:21 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756246908587489):** is the opto ready for me? maybe i can borrow the ipad when i get that
**15:22 [andy](https://slack.com/archives/C08TVA84PD4/p1756246934997769):** I just bought the ipad an hour ago, it'll come in a week or so
**15:22 [andy](https://slack.com/archives/C08TVA84PD4/p1756246979585439):** The opto is ready for you yes
**15:29 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756247373188729):** oh ok. if you have a minute can you remind me where in the project or which project the clickplate code is working?
**15:29 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756247379647849):**
![[F09BT8LJXP1_image.png]]
**15:29 [andy](https://slack.com/archives/C08TVA84PD4/p1756247388255369):** I was on the CCSD_WW proejct
**15:29 [andy](https://slack.com/archives/C08TVA84PD4/p1756247391562919):** it
**15:29 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756247397654519):** ok
**15:42 [Mason Radke](https://slack.com/archives/C08TVA84PD4/p1756248163784849):** ok got it figured out.. it was done with a message handler.. just had to update the script to match our actual tabs.. since it was imported from another project