Content
# #rancho-ynecita — 2025-10-29
**09:06 [Kevin](https://slack.com/archives/C09D358F91R/p1761754009544599):** @Mason Radke there is a folder in Box named Rancho Ynecita. Folder "Design" In there is a google doc "Rancho Ynecita SCADA Control Narrative"
> **09:16 [Mason Radke](https://slack.com/archives/C09D358F91R/p1761754591071549):** i dont have a design folder in there
> **09:16 [Mason Radke](https://slack.com/archives/C09D358F91R/p1761754605961469):**
> ![[F09P0RSUEK1_image.png]]
**09:07 [Kevin](https://slack.com/archives/C09D358F91R/p1761754029308009):** There is information in the begining of that doc to access the PC
**09:07 [Kevin](https://slack.com/archives/C09D358F91R/p1761754048596479):** I was planning on programming this myself back when you were tied up, but I didn't get far
**09:07 [Kevin](https://slack.com/archives/C09D358F91R/p1761754070378199):** I was going a bit overboard possibly in the narrative. I started a PLC program.
**09:08 [Mason Radke](https://slack.com/archives/C09D358F91R/p1761754082321199):** PLC is installed? and we're programming from a PC onsite there?
**09:08 [Mason Radke](https://slack.com/archives/C09D358F91R/p1761754094367549):** i think overboard on the narrative is better than not enough
**09:08 [Kevin](https://slack.com/archives/C09D358F91R/p1761754096366799):** PLC and PC are in the shop
**09:08 [Mason Radke](https://slack.com/archives/C09D358F91R/p1761754104563669):** ah, gotcha
**09:09 [Kevin](https://slack.com/archives/C09D358F91R/p1761754152349669):** I created a couple UDTs, and based the narrative I wrote around that.
**09:09 [Mason Radke](https://slack.com/archives/C09D358F91R/p1761754158297939):** do you have to share the folder with me?
**09:09 [Kevin](https://slack.com/archives/C09D358F91R/p1761754168198209):** Possibly. Standby
**09:11 [Kevin](https://slack.com/archives/C09D358F91R/p1761754317282259):** shared to your gmail
**09:13 [Kevin](https://slack.com/archives/C09D358F91R/p1761754388279309):** Feel free to redo the UDT's ,or scratch the whole program. I didnt' get far. But the UDT shows the data I'm interested in passing to and from SCADA.
**09:13 [Kevin](https://slack.com/archives/C09D358F91R/p1761754397782269):** PLC software is installed on the PC
**09:14 [Kevin](https://slack.com/archives/C09D358F91R/p1761754452385369):** here is some background:
**09:15 [Kevin](https://slack.com/archives/C09D358F91R/p1761754518485879):** there currently is a FRM DaqFactory system with RF SCADA boards
there are three remote sites (two wells, one tank)
**09:15 [Kevin](https://slack.com/archives/C09D358F91R/p1761754543013729):** our new plc will be the data concentrator and the system controller (logic)
**09:16 [Kevin](https://slack.com/archives/C09D358F91R/p1761754586549679):** the plc will communicated with the RFScada boards. I plan to figure this out in the field, so we will link IO later